UPS vs inverter vs battery energy storage: which does a factory need?
Three machines that all hold a battery, built for three different jobs. How each one switches over, how long it carries a load, and why most factories end up with more than one.
"We already have a UPS. Isn't a battery energy storage system just a bigger one?" It is a fair question, because a UPS, a home or shop inverter and a factory battery system all contain batteries and all take over when the grid fails. They are built for different jobs, though, and a factory that uses one for another's job either pays too much or gets caught out.
This guide compares the three, sets the diesel generator beside them, and explains which loads each should carry.
What is each one built to do?
- A UPS protects sensitive equipment: servers, network gear, PLCs, control panels, instruments. Its job is to keep that equipment running cleanly for minutes, long enough to ride through a short cut, wait for the genset or shut down safely. Power quality is part of the job, not only backup.
- An inverter, in the sense the word is used in Indian homes and shops, is a battery charger, a battery and an inverter that takes over a few circuits when the mains fails: lights, fans, computers. It is built for small loads and modest cycling, not for a production floor.
- A battery energy storage system (BESS) for a factory carries the production load itself, for an hour or more, several times a day if the grid fails that often, for years. It sits behind the meter, usually in a container in the yard, and works beside the diesel generator rather than in front of a single panel.
Put simply: a UPS protects equipment for minutes, an inverter keeps a few circuits alive, and a BESS keeps the plant producing through the short cuts.
How fast does each one take over?
This is where the differences start to matter on a factory floor. The IEC 62040-3 standard classifies UPSs by how their output behaves, and Schneider Electric's white paper on the different types of UPS summarises it:
- A double conversion online UPS feeds the load from its inverter all the time. When the input fails, the inverter simply draws on the battery; no switch operates, so the transfer time is 0 ms.
- Standby and line interactive UPSs normally pass mains power through and switch to the battery and inverter when the mains fails. The paper gives their transfer time as under 10 ms.
A home or shop inverter also switches over when it senses the mains has gone; its data sheet states the changeover time, and it is worth reading before plugging anything sensitive into it.
The battery system we build switches over in under 10 milliseconds. Its grid-forming inverter picks up the plant before motor contactors drop out, so machines carry on as if nothing happened. A diesel generator, by contrast, leaves the plant dark while it senses the failure, cranks and comes up to speed, and only then does the changeover transfer.
How do they compare side by side?
| UPS | Inverter | Factory BESS | Diesel generator | |
|---|---|---|---|---|
| Built for | Sensitive equipment | A few circuits in a home, shop or office | The production load through short cuts | Any load, for as long as there is fuel |
| Takes over | 0 ms (double conversion) or under 10 ms (standby, line interactive) | On its own changeover; see the data sheet | Under 10 milliseconds (our specification) | After it cranks and the changeover transfers |
| Carries the load for | Minutes, as usually sized | As long as its small battery lasts | Its rated duration: one or two hours of the load during a cut | As long as there is fuel |
| Sized on | The protected equipment | The circuits it feeds | The plant's load during a cut and its measured cut pattern | The plant's full load |
| Where it sits | In front of the equipment it protects | In front of the circuits it feeds | On the plant's bus, beside the genset | Through the changeover |
Why not just buy a bigger UPS?
Because a UPS is sized and built for minutes of support, while a battery that takes a factory's short cuts may be asked for an hour of support as often as the grid fails. Three things change when the job is the production load:
- Energy, not just power. Carrying a plant for an hour needs many times the battery a few minutes does. The battery becomes a large part of the cost, so its chemistry, cooling and cycle life decide the economics.
- Cycling. A battery that does the work of the genset for the short cuts is used hard. The LFP cells we use are rated for 6,000 cycles to 80% state of health, about thirteen years at the cycle count of our reference site.
- Working with the genset. A factory battery has to hand over to the genset cleanly when a cut runs long, and the genset's controller has to be told when to wait and when to start. That is a system design, not a box on a shelf.
A factory BESS is not a big UPS, and a big UPS is not a factory BESS. Our guide to battery energy storage for factories in India explains what goes into one.
Can a factory battery replace the UPS?
Usually it should not. A double conversion UPS gives a 0 ms transfer and conditions the power its equipment sees all the time. Servers and sensitive controls that need that should keep it. What changes when a battery system holds the plant's bus through a cut is how often the UPS has to work: it bridges milliseconds instead of carrying its load until the genset is up. The two sit at different points in the plant and do different jobs.
The same logic applies to the genset. A battery takes the short cuts; the genset stays for the long ones, the fire pump and the lift. What we build is a backup to your genset, not a replacement for it. Our guide on battery storage vs a diesel generator sets out why.
What does grid-forming mean, and why ask for it?
The US Department of Energy's explainer on inverters and grid services puts the difference plainly. Traditional grid-following inverters need an outside signal from the grid to know how to produce their sine wave. Grid-forming inverters generate that signal themselves, and can start up a grid that has gone down.
For backup, that is the whole question. When the grid fails and the genset has not started, there is no outside signal to follow. A grid-following battery system, of the kind built only for solar self-consumption or peak shaving, cannot carry the plant at that moment. Whatever you buy for backup, ask for grid-forming operation in writing, and ask how the supplier will demonstrate it.
Which should my factory have?
Most plants end up with layers, each doing the job it is good at:
- A UPS in front of servers, network equipment, PLCs and sensitive instruments, sized for minutes.
- A battery system beside the genset for the production load, sized on your load during a cut and your measured cut pattern, if your power fails often enough for it to pay.
- The genset for long cuts, the fire pump and the lift, as today.
An inverter has a place in a small office or a shop, not on a production floor.
Whether the middle layer is worth it depends on how often your power fails and how long a cut usually lasts, not on the size of your diesel bill alone. A battery earns only when it is used. Your DG controller has been counting both numbers for years; our guide to reading the start counter and engine hours shows where to look.
Run the numbers for your plant
Our savings calculator takes six inputs and shows the full working: what a unit from your genset costs, how much of its energy a battery for the short cuts would take, the size it would need and the payback, with a plain statement when it advises against going further. As a reference, typical payback is around three years at a plant spending about ₹30 lakh a month on diesel; smaller plants pay back more slowly.
Or start with the free ten-minute read of your DG panel: we photograph the start counter and engine hours, do the arithmetic and send you the numbers whether or not you buy. Call or WhatsApp +91 8920 110 530, or write to contact@vyut.in. More answers are on our FAQ.
What would it save your plant?
The savings calculator runs on your diesel spend and your belt's diesel price and shows the full working, including when the answer is no.