Battery storage vs diesel generator: why a factory needs both
A battery is instant and costs far less per unit. A genset runs for as long as there is fuel. For most factories the right answer is the battery for short cuts and the genset for long ones.
"Should we put in batteries and get rid of the genset?" It is a fair question. Battery prices have fallen a long way, diesel has not, and a battery has no exhaust, no fuel to manage and no engine to overhaul. For a factory, though, the honest answer is no: the two machines are good at different jobs, and the cheapest arrangement uses each for the job it does best.
This guide compares them, explains why we size a battery for the short cuts and leave the long ones to the genset, and covers the cases where a battery does not make sense at all.
What does each one do well?
A battery is fast and cheap to run. It takes over in under 10 milliseconds when the grid fails, quickly enough that motors and controls carry on as if nothing happened. A unit stored from the grid costs about ₹11.61 at our reference plant. It makes no exhaust on site, needs no fuel deliveries and is quiet. Its limit is energy: a factory battery holds one or two hours of the plant's load during a cut, not a day.
A diesel generator runs for as long as there is fuel in the tank. It is usually already bought and paid for, and building approvals often lean on it for the fire pump and the lifts. Its weaknesses are cost and speed: a unit from the genset costs about ₹27.70 at our reference plant once fuel, oil and maintenance are counted, and the plant goes dark while the set senses the failure, cranks and comes up to speed before the changeover transfers.
Put simply: the battery is the better machine for the first hour of a power cut, and the genset is the better machine for the fifth.
Battery vs DG set, side by side
| Battery energy storage | Diesel generator | |
|---|---|---|
| Takes the load when the grid fails | In under 10 milliseconds; machines do not see a break | After it senses the failure, cranks and comes up to speed; the plant sees a break |
| Cost of a unit at our reference plant | About ₹11.61 (grid power at ₹10.00 landed, 90% round trip, plus upkeep) | About ₹27.70 (diesel at ₹95.20 a litre, 0.27 litres per kWh, plus ₹2.00 oil and maintenance) |
| How long it can carry the plant | Its rated duration: one or two hours of the load during a cut | As long as there is fuel |
| Exhaust on site | None | Yes; in the NCR its use is regulated by the air quality commission |
| What wears it out | Cycles: 6,000 to 80% state of health, about thirteen years at a typical cycle count | Run hours and starts; short runs are the hardest duty |
| Cost of waiting | A few kilowatts for cooling and controls, about 3 kW at the reference site | Routine test runs |
| Upfront cost | Purchase and installation | Usually already owned |
Why not take the genset out altogether?
Three reasons, and any one of them is enough.
- Long cuts. Some cuts run four, six or eight hours. Carrying those on batteries means buying several times the storage, most of which would sit unused for most of the year. That is the most expensive kWh of storage you can buy.
- Fire pump and lift obligations. At most plants the fire pump and the lifts rely on the genset as their standby supply, and your building's approvals may depend on that arrangement. Keeping the genset commissioned, fuelled and under AMC leaves those obligations exactly as they are.
- Risk. Production should never depend on a single machine. With the genset kept, a battery out for maintenance or a cut that runs past the battery's energy simply means the genset starts, as it does today. You are never asked to bet uptime on a battery.
That is why we describe what we build as a backup to your generator, not a replacement for it. Chhote cuts battery lega. Lambe cut genset, jaise aaj.
Why does covering every power cut with batteries not pay?
Because most power cuts are short, and the energy in the long ones is spread over very few days.
A one-hour battery carries every cut from its first second. Most cuts end within the hour, so the genset never starts for them. For the cuts that run longer, the battery covers the start and the genset takes over. Added up over a year, a one-hour battery takes roughly half of all the energy the genset would have made, because most cuts end long before the hour is up. At our reference plant that is about 49% of the genset's energy, and a diesel bill cut of about 44%.
Now try to cover the other half. The second and third hours of storage are only used during the rarer long cuts, so each extra kWh you buy works far fewer times a year and earns far less. Chasing the long cuts costs about two and a half times the money for a worse return. That is the genset's job, and it is already paid for.
The same logic explains why the size of your diesel bill does not decide the case on its own. Two plants with the same fuel bill can have very different paybacks: one burns its diesel in hundreds of short cuts that a battery would carry, the other in a handful of long ones it would not. Our guide on what a DG unit really costs shows where the money goes.
One-hour or two-hour battery: how is it chosen?
Two numbers set the size, and neither is a matter of taste.
- Power (kW) is your plant's load during a power cut. It is a property of your factory, not a choice.
- Duration (hours) is chosen from the average length of your power cuts, measured at your DG controller. Engine hours divided by the number of outage starts gives it, once test runs are taken out. Our guide to reading the start counter and engine hours shows how.
Where cuts are short, a one-hour pack is right. Where they run longer, a two-hour pack is. On a site averaging two and a half hours, the two-hour pack displaces roughly two thirds more diesel for the same payback, so getting this choice right is worth more than any discount. We make the choice from your measured numbers and explain it, rather than handing you a menu: the duration is a decision your controller data settles better than a brochure can.
What happens during a power cut with both on site?
- The grid fails. The battery's grid-forming inverter picks up the plant in under 10 milliseconds. Machines keep running: no restart, no scrapped batch, no wait while the genset cranks.
- The genset waits. Its controller is told not to start. Modern DG controllers have a standard input for exactly this, and the change is made through your DG service agency, in writing.
- Short cut: the grid returns. The plant goes back to the grid and the genset never started. The battery recharges from the grid, outside your peak window so it does not push your maximum demand up.
- Long cut: the genset starts. If the cut runs on, the genset starts automatically and takes the plant, just as it does today. Fire pump and lift arrangements are untouched throughout.
- Everything is metered. A dedicated energy meter records every unit the battery delivers in place of the genset. That metered figure, not a model, is what a saving guarantee is settled against each month.
When does a battery beside the genset not make sense?
- Your power rarely fails. A battery earns only when it is used. If your grid is reliable, the battery will sit charged and idle, and no amount of diesel saved per cut makes up for that. We would rather tell you so after a ten-minute read of your controller than after you have bought anything.
- Your grid tariff is very high relative to diesel. The saving is the gap between a diesel unit and a stored grid unit. If that gap closes, so does the case.
- Your cuts come so close together that the battery cannot recharge between them. A pack caught half charged misses cuts it was counted on to carry. Interval data settles this before any figure is issued.
- The payback runs past four years. Beyond four years we advise against buying: battery prices are falling about 10 to 15% a year, so at that payback, waiting and buying later is likely to serve you better than buying now. Up to four years we show you the payback and you decide. The saving guarantee is written only where the modelled payback is three years or better. As a reference, typical payback is around three years at a plant spending about ₹30 lakh a month on diesel; smaller plants pay back more slowly, because approvals and commissioning cost much the same at any size.
See what it would do at your plant
Our savings calculator takes six inputs and shows the full working: your cost per diesel unit, how much of your genset's energy a battery would take, the size it would need, the payback, and the conditions under which it advises against going further. For more on how battery systems work and how they are bought, read our guide to battery energy storage for factories in India.
The two numbers that decide the case are on your DG controller already. We will read the start counter and engine hours for free, in about ten minutes at the panel, and send you the result whether or not you buy anything. Call or WhatsApp +91 8920 110 530, or write to contact@vyut.in. Common questions are answered on our FAQ.
What would it save your plant?
The savings calculator runs on your diesel spend and your belt's diesel price and shows the full working, including when the answer is no.