Battery energy storage for factories in India: a plain guide
What a commercial and industrial battery is, how long it lasts, how it takes over when the grid fails, how it should be sized, what the CEA's new safety rules require, and how buying one works.
Battery energy storage has moved from grid projects and telecom towers into factory yards. For an Indian plant the usual reason is not green credentials but diesel: a battery that takes over the short power cuts runs the plant on stored grid power at well under half the cost of a unit from the genset. This guide explains what such a system is, what to ask about it, and how to tell whether it suits your plant.
What is a commercial and industrial battery energy storage system?
A commercial and industrial (C&I) battery energy storage system, or BESS, is a set of battery racks with the equipment to use them safely, usually in a container on a plinth in the yard:
- Cells and racks, which store the energy.
- A battery management system, which watches every cell's voltage and temperature and stops the battery before it leaves safe limits.
- A power conversion system, the inverter, which turns the battery's DC into the AC your plant runs on and back again for charging.
- Controls, which decide when to charge and when to carry the plant.
- Cooling, because cells last longest within a narrow temperature band, and an Indian summer is outside it.
A factory system sits behind the meter, on your side of the DISCOM's meter, and ours is non-exporting by default: it never sends power back to the grid. It is not a big UPS. A UPS carries a site for minutes so it can shut down safely. A factory BESS carries the production load for an hour or more, several times a day, for years.
One specification matters more than any other for backup: the inverter must be grid-forming. A grid-following inverter needs the grid's voltage to follow, so when the grid fails it cannot hold the plant up. Batteries built only for solar self-consumption or peak shaving may never need to run without the grid. For backup, ask for grid-forming in writing and ask how the supplier will demonstrate it.
The system we build is a block of this kind (LFP cells, a liquid-cooled container and a grid-forming inverter) that sits beside your existing DG set and takes over the short cuts. It is a backup to your genset, not a replacement for it. Our guide on battery storage vs a diesel generator explains why the genset stays.
Why LFP chemistry, and how long does it last?
Lithium iron phosphate (LFP) has become the standard chemistry for stationary storage. It uses no cobalt and no nickel, and it is the most stable lithium chemistry in common use. It stores a little less energy per kilogram than the chemistries used in phones and many cars, which matters in a car and hardly at all in a factory yard.
Battery life is counted in cycles. One equivalent full cycle is a full discharge and recharge, or the same energy spread over several partial ones. The cells we use are rated for 6,000 cycles to 80% state of health: after that much use the battery still holds about 80% of its original energy. At our reference site the pack runs about 460 equivalent full cycles a year, so:
- 6,000 cycles ÷ about 460 a year = about thirteen years of asset life.
Your cycle count is set by your power cuts, not by choice. A battery cannot cycle more often than the grid fails, which is why a factory with frequent cuts uses a battery hard and one with reliable power barely uses it at all.
Two running costs to know about. Round-trip efficiency is 90% AC to AC, including the power conversion system, so about a tenth of the energy put in is lost. And the battery draws a few kilowatts for cooling and controls while it waits for the next cut, about 3 kW at the reference site; we deduct that standby power from every saving we show.
How fast does it take over when the grid fails?
Our system's specification is a switchover in under 10 milliseconds. That speed is the whole point. Today, when the grid fails, the plant goes dark while the genset senses the failure, cranks and comes up to speed, and the changeover then transfers. Contactors drop out, machines stop, a process batch may be scrapped. A grid-forming battery picks the load up before most machines notice anything happened.
Ask any supplier for the transfer time in writing, and tell whoever sizes the system about your most sensitive loads. Equipment with long restart sequences, large chillers for example, can take many minutes to come back after a trip, so holding them through the cut is worth more than the diesel alone suggests.
How should a factory battery be sized?
Three numbers decide the size, and all three come from measurement, not a catalogue:
- Power (kW): your plant's load during a power cut. Not your sanctioned load and not your DG rating, but what the plant actually draws when it is running on the genset.
- Duration (hours): chosen from your measured average cut length. Where cuts are short, a one-hour pack is right; where they run longer, a two-hour pack. On a site averaging two and a half hours, the two-hour pack displaces roughly two thirds more diesel for the same payback. We choose it from your numbers and explain why.
- Frequency: how often your power fails. This does not change the size, but it decides whether the battery pays at all, because it earns only when it is used.
Your DG controller already holds the last two. Engine hours and the lifetime start count give both, once test runs are taken out; our guide to reading the start counter and engine hours shows how.
Resist the urge to size for every cut. A one-hour battery takes roughly half of all the energy a genset makes in a year, because most cuts end long before the hour is up. Chasing the long cuts costs about two and a half times the money for a worse return, and the genset is already there for them.
Two practical checks belong in the sizing too. The pack needs time to recharge between cuts, so cuts that come very close together reduce what it can carry. And it should recharge outside your peak window, so it does not push your maximum demand up; if your tariff makes that impossible, the economics change and you should be told so. Systems start around 100 kWh; most of what we build is a few hundred kWh to a few MWh, for plants spending about ₹5 lakh a month or more on diesel.
Does battery storage work with rooftop solar?
Yes, and it fixes a problem many plants with solar have noticed: bijli gayi, solar bhi gaya. A grid-tied solar inverter must shut down within about two seconds of losing the grid, a safety requirement known as anti-islanding. It cannot simply run on the genset either, because an alternator cannot absorb power pushed back into it, which is why most sites keep the solar off whenever the generator runs.
A grid-forming battery presents the voltage and frequency the solar inverters look for and absorbs any surplus, so the array keeps producing through a cut. That creates two possible gains: generation you currently lose during cuts, and recharging the battery from the sun instead of the grid where you export power today. Before counting either, three things need checking: whether your existing inverters will synchronise to a battery-formed grid, whether the pack has cycles to spare, and what your meter actually pays for an exported unit.
We keep solar outside the diesel case. The payback we quote is the diesel-only one, both solar streams are reported separately in our calculator, and both sit outside the saving guarantee.
Is it safe, and what do the CEA regulations require?
The safety case starts with chemistry and construction: LFP cells, cell-level monitoring, liquid cooling and rack-level fault isolation, in a container with its own fire detection and suppression.
The regulation is new. The Central Electricity Authority notified the CEA (Measures relating to Safety and Electric Supply) Amendment Regulations, 2026 on 27 March 2026. They add a Chapter XA on battery energy storage and come into force on 1 April 2027. Among its requirements:
- Two-fault tolerance: the system must operate or shut down safely even after two independent faults.
- Fire and explosion protection at cell, module, rack, container and site level, with explosion protection through forced ventilation and automated louvers.
- A battery management system that monitors and records voltage, temperature and thermal runaway at cell, module and rack level.
- Detection for smoke, gas, heat and flame, and automatic fire suppression in every battery container.
- Ventilation and cooling, with a shutdown if mechanical ventilation fails.
- Fencing at least 1.8 m high, CCTV and alarms, and emergency stops.
- An independent third-party fire safety audit, submitted to the Electrical Inspector.
Two honest caveats. The detailed clauses apply to installations connected above 650 V; installations at 650 V and below must comply with the relevant standards. And the CEA is to publish its list of relevant standards within three months of the regulations coming into force, so until then, ask any supplier which standard they certify against. Separately, state approvals gate energisation: in Haryana, that means the Electrical Inspectorate.
Buying it: ownership, payback and the four stages
You own it. We sell the system outright. You own it from day one, with no lien and no multi-year contract over your plant's electrical system, and your own CA confirms the depreciation treatment. If you want bank finance, the calculator shows the EMI on your terms.
Payback. Typical payback is around three years at a plant spending about ₹30 lakh a month on diesel. Larger plants do a little better, smaller ones more slowly. Up to four years, we show you the payback and you decide. The saving guarantee is written only where the modelled payback is three years or better, on your measured cut count, invoiced diesel and landed tariff, with a diesel price floor and a tariff ceiling, settled monthly against a physical meter. If we miss it, we pay the difference.
The four stages:
- Indicative model, today: our calculator on your diesel spend and your belt's figures. Ten minutes, no cost.
- Measured baseline, weeks 1 and 2, at our cost: your controller's start counter, the DG logbook and your fuel invoices, with a logger only where those leave a gap. You keep the data whether or not you buy.
- Verified proposal, week 3: the model re-run on your measured numbers, at a fixed price, with the guarantee issued.
- Deploy and settle, week 4: deployment and commissioning, subject to the units being in stock, then monthly settlement on metered displaced kWh.
What we can and cannot show you: the configuration is proven in India (AmpereHour Energy commissioned a 1.5 MW / 4 MWh behind-the-meter system at Cummins in Phaltan, Maharashtra, in February 2025; not our project). We have no completed installation of our own to show you yet, and we will not present modelled figures as delivered results.
Next step
Run your plant through our savings calculator: six inputs, the full working, and a plain statement when it advises against going further. To see what each diesel unit costs you today, read what a unit from a DG set really costs.
Or start with the free ten-minute read of your DG panel: we photograph the start counter and engine hours, do the arithmetic, and send you the numbers whether or not you buy. Call or WhatsApp +91 8920 110 530, or write to contact@vyut.in. More answers are on our FAQ.
What would it save your plant?
The savings calculator runs on your diesel spend and your belt's diesel price and shows the full working, including when the answer is no.